Darkglass Electronics
Darkglass Electronics Microtubes X Multiband Distortion
The Darkglass Electronics Microtubes X Multiband Distortion brings the studio method producers have been using the years to cover the whole bass distortion spectrum: from articulate high gain to punchy mild overdrive, raw and gnarly fuzz and everything in between. You now have absolute control in constructing your vision of what the perfect bass distortion texture, definition, and size should have.
You now have absolute control in constructing your vision of what the perfect
bass distortion texture, definition, and size should have.
Controls:
High-pass frequency: Controls the cutoff frequency to be distorted, ranging from 100Hz (for thicker, fuzzier saturation) or 1kHz for ultra-sharp definition.
Low-pass frequency: Controls the cutoff frequency to be mixed back to the high-pass side. Ranging from 50Hz (for only sub-bass) and 500Hz to preserve some clean mids.
Level: Sets the overall output volume of the unit.
Drive: Sets the amount of distortion for the high pass side.
Mix: Sets the blend between low-pass and high-pass signals.
Mids: Active mid control placed after the Mix control. +-12dB @ 500Hz.
Input: 1/4" connector for the instrument.
Technical Specifications
Input Impedance 1MΩ Output Impedance 1kΩ Current Consumption 30mA Voltage 9V DC (Center Negative) Dimensions Width 75 mm (2.95 in) Height 111 mm (4.37 in) Depth 43 mm (1,77 in) Weight 250 g (0.55 lb) Power: The Darkglass Electronics Microtubes X Multiband Distortion has a current draw of 30mA. Only use a regulated 9V DC adapter with a center-negative plug. Due to ecological reasons it does not accept batteries. Warning: Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.
Disclaimer
In the interest of continuous improvement, specifications are subject to change without notice. If you have any questions, please don’t hesitate to contact us at www.darkglass.com.
Note: Due to the value of the Darkglass Electronics Microtubes X Multiband Distortion we may require that an adult be present to accept delivery.
You now have absolute control in constructing your vision of what the perfect
bass distortion texture, definition, and size should have.
Controls:
High-pass frequency: Controls the cutoff frequency to be distorted, ranging from 100Hz (for thicker, fuzzier saturation) or 1kHz for ultra-sharp definition.
Low-pass frequency: Controls the cutoff frequency to be mixed back to the high-pass side. Ranging from 50Hz (for only sub-bass) and 500Hz to preserve some clean mids.
Level: Sets the overall output volume of the unit.
Drive: Sets the amount of distortion for the high pass side.
Mix: Sets the blend between low-pass and high-pass signals.
Mids: Active mid control placed after the Mix control. +-12dB @ 500Hz.
Input: 1/4" connector for the instrument.
Technical Specifications
Input Impedance 1MΩ Output Impedance 1kΩ Current Consumption 30mA Voltage 9V DC (Center Negative) Dimensions Width 75 mm (2.95 in) Height 111 mm (4.37 in) Depth 43 mm (1,77 in) Weight 250 g (0.55 lb) Power: The Darkglass Electronics Microtubes X Multiband Distortion has a current draw of 30mA. Only use a regulated 9V DC adapter with a center-negative plug. Due to ecological reasons it does not accept batteries. Warning: Unregulated power supplies and/or higher voltages may result in suboptimal noise performance and even damage your unit, voiding the warranty.
Disclaimer
In the interest of continuous improvement, specifications are subject to change without notice. If you have any questions, please don’t hesitate to contact us at www.darkglass.com.
Note: Due to the value of the Darkglass Electronics Microtubes X Multiband Distortion we may require that an adult be present to accept delivery.
